请高手支招。

kathy_d

最近。
电脑出现了个问题。
机器开一段时间。
大概是三小时以上。
偶尔出现蓝屏死机的情况。
而且重启也不解决问题。
因为根本进不了系统。
黑屏白字。
说是找不到操作系统。
安全模式也进不了。
这是什么原因？
是机器太老？
还是其他原因？

顽石不泪

应该是开机时间长 温度过高
或许是因为风扇和散热系统灰尘累积太多
下次记下蓝屏代码查下
或者送到维修站检测下（但是最好不要轻易听信他们的维修建议）

小奸商

DESKTOP OR LAPTOP?如果是DESKTOP的话,建议你清清灰尘,擦擦显卡以及内存条的金手指,然后检查下风扇散热的问题
如果是LAPTOP的话,建议你重新检查下内存条,看是否松动

kathy_d

谢谢石头和菜小猪哈.

小奸商

...........为啥是菜小猪///// [s:239]

飞翔的鹰

引用第4楼小奸商于2008-04-11 17:38发表的 :
...........为啥是菜小猪///// [s:239]

你是用来下酒菜的小猪

kathy_d

石头说把代码抄下来，具体如下：
A problem has been detected and windows has been shut down to pretent damage to your computer.
KERNEL_DATA_INPAGE_ERROR
If this is the first time you've seen this stop error screen,restart your computer.If this screen appears again,follow these steps:
Check to make sure any new hardware or software is properly installed.If rhis is a new installation,ask your hardware or software manufactuerer for any windows updates you might need.
If problems continue,disable or remove any newly installed hardware or software.Disable BIOS memory options such as caching or shadowing.If you need to use safe Mode to remove or disable components,restart your computer,press F8 to select Advanced startup options,and then select safe Mode.
Technical information:
***STOP:0X0000007A(XC0202344.0XC000000E,0X808D1E45,0X052A0860)

小奸商

KERNEL_DATA_INPAGE_ERROR
是内核数据写入出错了
根据微软的信息,和长时间来众多人的经验和解决方案,得出了如下解决方法,我直接COPY给你吧,不过是英文的,你好好看看吧,不难看懂的.
[s:251]

Error Message:

KERNEL_DATA_INPAGE_ERROR
Explanation:

This Stop message indicates that the requested page of kernel data from the paging file could not be read into memory. This Stop message is usually caused by a bad block (sector) in a paging file, a virus, a disk controller error, or failing RAM. In rare cases, it is caused when nonpaged pool resources run out. It is also caused by defective hardware.
User Action:

If the I/O status is C0000185 and the paging file is on a SCSI disk, the disk cabling and SCSI termination should be checked for problems. Check your computer for viruses, using any up-to-date, commercial virus scanning software that examines the Master Boot Record of the hard disk. An I/O status code of 0xC000009C or 0xC000016A normally indicates the data cannot be read from the disk due to a bad block (sector). If you can restart the system after the error, Autochk runs automatically and attempts to map out the bad sector. If Autochk does not scan the hard disk for errors, manually launch the disk scanner. Run Chkdsk /f /r on the system partition. Restart the system before the disk scan begins. If you cannot start the system due to the error, use the Recovery Console and run Chkdsk /r. Caution: If your system partition is formatted with the FAT file system, the long file names used by Windows 2000 can be damaged if Scandisk or another MS-DOSbased hard disk tool is used to verify the integrity of your hard disk from an MS-DOS prompt. (An MS-DOS prompt is typically derived from an MS-DOS startup disk or from starting MS-DOS on a multiboot system.) Always use the Windows 2000 version of Chkdsk on Windows 2000 disks. Another common cause of this Stop message is failing RAM. Run hardware diagnostics supplied by the system manufacturer, especially the memory scanner. For details on these procedures, see the owners manual for your computer. Check that all network adapters in the computer are properly seated. Use an ink eraser or an electrical contact treatment, available at electronics supply stores, to ensure network adapter contacts are clean. Check the System Log in Event Viewer for additional error messages that might help pinpoint the device causing the error. Disabling memory caching of the BIOS might also resolve it. Finally, if all the above steps fail to resolve the error, take the system motherboard to a repair facility for diagnostic testing. A crack, a scratched trace, or a defective component on the motherboard can also cause this error. For more troubleshooting information about this Stop message, refer to the Microsoft Knowledge Base at http://support.microsoft.com/support.

小奸商

还有条中文的解决方案,不过很不详细,而且也比较片面的说,也给你吧

解决方案:首先用升级为最新病毒库杀毒软件查杀病毒, 如果促无信息中还0xC000009C
或0xC000016A代码, 那么表示是坏簇造成的, 并且系统的磁盘检测工具无法自动修复, 这时要进入"故障恢复控制台", 用"chkdsk /r"命令进行手动修复.

kathy_d

谢谢菜小猪筒子。
[s:251]

水桶

手都比我高。嗯！！看不懂！！

kathy_d

开始以为是硬盘出了问题。
早上起床后开机。
都进不了系统。
于是心一横。
一键还原。
现在貌似还正常。
有时间了好好重装一次。